current location:Home>News>Industry News

Latest News

Contact Us

Address: 3F , Blg 7 West, Sinosteel Building,Maque Industry Village Nanshan,Shenzhen,518057,Guangdong

Phone: +86-755-26971006

Mobile: 13751075276

Email: sales@acroview.com

Acroview IPS5200S IC Programmer update to support programming FuDanWei's serial flash memory FM

Time:2023-05-16   Visits:1896

     The leader in the chip programming industry - Acroview Technology recently released the latest programming software update and a list of newly supported chip models, among which FuDanWei's serial flash memory FM25Q64AI3 has been supported by Acroview's general programming platform AP8000.


     FM25Q64AI3 is a 64Mbit (8Mbyte) serial flash memory with advanced write protection mechanism. FM25Q64AI3 supports standard serial peripheral interface (SPI), dual/quad I/O and 2-clock instruction cycle quad peripheral interface (QPI). They are ideal for hiding code into RAM, executing code directly from dual/quad SPI (XIP), and storing voice, text, and data.


     FM25Q64AI3 can use Page Program command to program 1 to 256 bytes at a time. It is designed to allow single sector/block or full chip erase operations at a time. FM25Q64AI3 can be configured to protect part of the memory in software protection mode, the device can sustain at least 100K program/erase cycles on each sector or block.


emmc ic programmer


Characteristic:


• 64Mbit flash memory

– 2048 unified sectors, 4K bytes per sector

– 128 uniform blocks of 64K bytes each, or

– 256 uniform blocks of 32K bytes each

– 256 bytes per programmable page

• Wide operating range

– 2.3V~3.6V single voltage power supply

– Industrial temperature range

• serial interface

– Standard SPI: CLK, CS, DI, DO, WP

– Dual SPI: CLK, CS#, DQ0, DQ1, WP#

– Four SPI: CLK, CS#, DQ0, DQ1, DQ2, DQ3

– QPI: CLK, CS#, DQ0, DQ1, DQ2, DQ3

– Continuous read mode support

– Program/erase suspend and resume support

– Allows true XIP (execute-in-place) operations

• high performance

– Maximum fast read clock frequency: 104MHz

– Maximum read clock frequency: 66MHz

– Typical page program time: 0.6ms

– Typical sector erase time: 45ms

– Typical block erase time: 120/150ms

– Typical chip erase time: 20 seconds

• Low power consumption

– Typical Deep Power Down Current: <1µA

• Safety

– Software and hardware write protection

– Lockable 4X256 byte OTP security page

– 64-bit unique ID for each device

– Discoverable parameters (SFDP) register

• High reliability

– Endurance: 100,000 program/erase cycles

– Data retention: 20 years

• Green packaging

– 8-pin SOP (150mil)

– 8-pin SOP (208mil)

– 8-pad TDFN (5×6mm)

– 24-ball BGA (8x6mm)

– All packaging is RoHS Compliant and Halogen Free


ic programmers.png



Internal block diagram


The AP8000 universal ic programmer machine independently developed by Angke Technology includes three parts: the host, the base plate, and the adapter seat.

ufs programmer


The host supports USB and NET connections, allowing multiple IC Programmers to be networked to achieve the purpose of simultaneously controlling multiple programmers to burn at the same time. The built-in chip safety protection circuit ensures that even if the chip is reversed or a short circuit caused by other reasons can be detected immediately and the power will be cut off to ensure the safety of the chip and programmer. Embedded high-speed FPGA greatly accelerates data transmission and processing. There is an SD card slot on the back of the main unit. Put the project file produced by the PC software into the root directory of the SD card and insert it into the card slot. The project file can be selected, loaded, and programmed through the buttons on the programmer. command, in order to achieve the purpose of operating without PC, which greatly reduces the cost of PC hardware configuration, and can be conveniently and quickly matched with the working environment.


AP8000 makes the mainframe more expandable by adding an adapter board to the backplane. Currently, it supports devices produced by all mainstream semiconductor manufacturers, including TI, ST, MicroChip, Atmel, Hynix, Macronix, Micron, Samsung, Toshiba, etc. Supported device types include NAND, NOR, MCU, CPLD, FPGA, EMMC, etc., and support file formats including Intel Hex, Motorola S, Binary, POF, etc.



Company Profile



About Fudan Microelectronics: Fudan Microelectronics (FuDanWei) was established in 1998. It has formed four mature product lines and system solutions of security and identification, smart meters, non-volatile memory, and smart appliances. The products are sold in more than 30 countries and regions. . Security and identification products are widely used in finance, social security, urban public transportation, electronic certificates, mobile payment, anti-counterfeiting and traceability and other fields.


About Acroview Technology: ACROVIEW is a leading global provider of semiconductor chip burning solutions. The company insists on changing the world with technology, driving the future with intelligence, and continuously creating value for customers. Acroview's AP8000 flash ic programmer platform and the latest IPS5000 programming automation solution provide one-stop solutions for customers in the semiconductor and electronics manufacturing fields. The company has served global leading customers including Huawei, BYD, Foxconn and so on.

Hot tags:

烧录器| ic烧录机| IC自动烧录机| 芯片烧录设备| 自动化烧录器| 全自动ic烧录机| IC自动化烧录器| 万用型烧录器| IC自动烧写器| 在线自动化烧录机| ic芯片烧录机厂家| 芯片自动烧录器| 芯片自动烧录机| 自动编程烧录器| 全自动芯片烧写器| 全自动在线烧录机| 自动ic烧录机厂家| 自动化ic烧录机| 芯片烧录器厂家| 全自动在线烧录机|
memory ic programmer_Production Programmers_eMMC Programmer

Dear, scan to add WeChat as a friend